Get a
GRIP in the Snow:
Easy Tire Chains & Some Helpful
Hints!
by Bill
Burke
|
Grip 4x4
Chains
$193.80. / 2
sets (plus shipping)
2 pairs = 4 chains /
4 Tires - 4 Chains!
This price is for all sizes.
We do not
sell single
pairs of Grip 4x4 chains.
*NOTE: We do not stock Grip 4x4
Chains. They are drop-shipped
from RUD's warehouse
 
|

Click on graphic to order
Bill's
2-hour recovery DVD
from one
of our Dealers.
DVD
includes
RUD chain
demonstration by
Bill.
|
Snow 4-wheeling is great,
chilling fun, and coldly challenging. In the wintry Colorado
back country (and many other parts of the world) where the
first snow usually falls in October, then stays til late
June, early July, where sometimes high mountain passes like
Pearl Pass and Webster Pass stay closed til mid-September,
it can be finger-numbing and downright dangerous.
We've all seen the TV
commercials for the winter sales of the fancy new 4WD
bounding across snow fields, blasting fresh powder all over
the camera! It looks like such fun! One problem with this
scenario is that you have to watch out for tree stumps and
rocks hidden by the deep, fresh powder. Blast across some
meadows and your tire could get shoved under your rig,
bending the rim and flattening the tire. OUCH!
Be careful when the
momentum factor carries you away. Too fast, and the rig will
slide off the trail. The ice under the snow will ensure
that. You can be "clipping" down a trail in deep powder,
come into a turn, try to negotiate the turn and the rig
continues straight. Here is where tire chains come in handy.
This article is going to talk about what I feel are some of
the most important pieces of equipment to help get you and
your rig ready for the winter trail, tire chains in general,
and the GRIP 4X4 chains specifically.
In 1996, I attended the
SEMA (Specialty Equipment Market Association) show in Las
Vegas and looked at the various types of tire chains offered
by different manufacturers. After seeing many diverse types
of chain construction, I decided that the style of the GRIP
4X4 by RUD-Chain, Inc. seemed to be the most efficient for
installation. One of the most important
features I was looking for was that, in a sticky situation,
they needed to be quick and easy to install. RUD provided me
with chains for both my Defender 90 and my Range Rover to
test for my purposes.
I usually use chains
whenever I do any back country driving in the snow--4 tires,
4 chains. I've even written articles in the past on how to
install tire chains, when to use them, and how to keep them
from twisting up. But, now I've found a much better
way!
The GRIP 4X4 chains are
the easiest I've ever put on! They have a plastic encased
steel cable on the inside of the tire that helps locate the
cross bar links, and helps keep the chain from hitting the
springs or radius rod when turning the front wheels. They
also have chain links that connect the cross bar links. This
would be considered a modified diamond pattern. These run
parallel with the tire and help keep the vehicle from
sliding sideways like standard ladder style
chains.
It
literally takes a half a minute to install a chain on
a tire. I was knee- deep in snow on a side hill with
the D-90 in the bushes--the lockers and the Mudders
had done their best to get me there! I installed all
four GRIP 4X4 chains in minutes and didn't have to
move the tires at all to get the chains tight! I then
drove right out of the
predicament.
That's right, the tires
did not have to be rolled or the vehicle moved to install
these chains. Although it is a good idea to roll down the
road about 50 feet and make sure the chains are properly
tensioned, in a tight spot like I had on the trail they
worked just fine without doing this.
Top of
Page
It's as simple as sliding
the chain behind the tire, bringing the inner cable
connector up to the top and making the connection for the
inner link, then connecting the outer link, straightening
the chain on the tire, pulling the tensioning chain through
the locking mechanism, pulling tight, then hooking it to an
appropriate link to keep the chain tensioned. Installing the
GRIP 4X4 chains is that easy!
I was in my Range Rover
and a little abusive to the chains during an excursion up
Left Hand Canyon in Boulder, Colorado on a very snowy and
cold Saturday in January. It was quite miserable weather,
prime conditions and a great trail to test a set of
chains--they worked really well on the open-diff Range
Rover. Sometimes running open-diffs in snow and ice
conditions is better than using lockers, as lockers tend to
slide you sideways. Although, with the GRIP 4X4's design,
side slip is minimized. Another feature I like is the GRIP
4X4's are reversible, so the chains last longer, unlike
standard ladder-type chains that cannot be
reversed.
For pricing and
other information about these chains,
call us at 970-858-3468.
Chains can also be
used for worn or non-aggressive tread tires when the trail
turns to mud or loose rock. They can make your rig into a
little tractor! If you can only afford one set, and you're
going to be in 4WD on a trail, I recommend putting them on
the front axle since you have steering, braking, and
traction. However, be careful on long descents since you're
getting such good traction with the front end, and the rear is not
chained, it may swing around on you. So it might be better for those
descents to chain up the rear. That's why I like RUD chains because
they are so easy to move around.
Other suggestions for using chains
include:
1. Use caution
with spinning the tires, as the chains may catch on
unseen stumps, rocks, and roots, and you could brake an
axle or a hub.
2. Check the trail
ahead in deep snow for hidden obstacles.
3. Inspect chains
before and after each outing. Look for worn links and
stretched connectors.
4. Spray chains with
some WD40 after each use. Make sure the chains don't
rust. Don't leave them in a pile!
5. Be careful when
steering with the front end articulated. Keep the chains
from contacting vehicle components.
6. Remember, chains
will allow you to dig to the trail through deep snow and
ice. Watch for high-centering in those conditions.
Sometimes, through very deep, hard-packed snow, I have
used soft, high flotation tires to go across the top of
deep drifts in lieu of chains. Then I've aired up to put
the chains back on.
7. Do not use bare
hands on cold, icy chains. Use heavy-duty neoprene/rubber
gloves or good leather work gloves to put chains
on.
8. Drive very slow and
deliberate with chains on to gain proper traction and
control on the icy trail.
9. Occasionally, I'll
use higher RPM's in lower gears to keep the chains
"churning." This breaks the ice in hard-pack snow so the
vehicle can gain traction on the trail.
If you want to see how
effortless the GRIP 4X4 chains are to put on and you're in
the neighborhood, call me and I'll be happy to demonstrate
them for you! I like these chains! If you want to
order a set please call 4-Wheeling America @ 970-858-3468. These chains must be sized according
to the tire. They are very specific for tire size, i.e., not
generic sizing.
Whether you use your rig
to navigate wintry streets to get groceries and the kids to
school, or winch to that great ice fishing spot, you need to
be prepared for any incident. Winter is nothing to be
trifled with. Have the proper equipment and a plan on how to
use it, if necessary. You can have all the gear in the
world, but it's no good if you don't know how to use it and
you don't have a plan! Get proper training in vehicle
operation. Take some emergency training through your local
Red Cross office. Be aware of your limitations and those of
your vehicle.
No matter what kind of rig
you own, from stock showroom vehicle to the most radical of
off-road machines, you must always check it out before
heading to the hills. You can prepare a checklist to be sure
you have seasonal items that maybe wouldn't make it into
your kit other times of the year. I built a shelf in my
garage to hold the off-season items. That way, it goes in
the vehicle and when I'm done, it goes right back on the
shelf in its place. I think it was Confucius who said: "A
place for everything and everything in its place," or maybe
it was my drill sergeant.
It sure is a winter
wonderland out there...quiet, peaceful and scenic. The best
part about winter 4-wheeling is the lack of bugs and people
competing for campsites! Be prepared, stay safe, and
don't be a stick-in-the-mud (or snow)!
Top of
Page
For pricing
and to order RUD Grip 4x4 chains,
call us at 970-858-3468.
Basic Rules for Using
All Tire Chainsa
1. Pre-fit chains
prior to actual use.
2. Consult owner's
manual to see if chains can be used on your
vehicle.
3. Make sure chains are
properly sized for your tire (see article
above).
4. Follow directions
for installing tire chains. Apply as tightly as possible
by hand for maximum chain life.
5. Be sure to pull
off-highway to safe place before installing, servicing,
or removing tire chains.
6. Do not deflate tires
to install tire chains. (Tires should be normal
inflation.)
7. Drive approximately
1/4 mile. Stop and retighten. Extra links (depending on
chain style) may be cut off, or preferably, retained on
the fastener arm. Keep chains tight to snug throughout
the operation. Only after retightening may rubber
adjusters be applied. DO NOT USE ADJUSTERS ON "ALL
CABLE-TYPE" CHAINS.
8. Do not exceed 30
miles per hour. Accelerate and decelerate slowly. Avoid
spinning or locking of wheels.
9. If a cross-chain
should fail, stop immediately. Repair or remove. DO NOT
DRIVE WITH A BROKEN CHAIN.
10. Avoid hitting curbs
with tire chains.
11. Tire chains are not
designed for towing.
RUD Product Catalog,
1997.
©Bill Burke’s
4-Wheeling America LLC
Top of
Page
|

Back
to Articles
|